Forum - Topic


Picanto II Front dent


Forum Picanto / Morning II TA Picanto II Front dent

Manuals  |  Advert  |  Model Kia Picanto / Morning II TA  |  Our vehicles

Disscussion about vehicle

2015 Picanto / Morning 1.0 (61 cui)

4 discussions

Fuel gasoline. 5-speed Manual transmission. Engine 1 000 ccm (61 cui), 3-cylinder, In-Line.



2017-03-30 01:12:46

Hello,

My name is Nicolas and i have a Picanto 2015. There is a dent in the fender RH panel. Is there a method to repair the dent not taking the car to workshop? Also, as you can see in the picture, it looks like its necessary to remove the front light assy to get access to that area. Is there a manual that can guide me in the removal of the front light.

Thanks and good luck.

e34e36  
2017-03-31 09:49:28

Hi, for the dent try a trick with hot water or compressed gas, see the youtube videos, if it works you dont need to remove the front light.

Car Dent Repair With Hot Water And Toilet Plunger DIY  |  More info

Not only can you unclog a drain with a plunger, you can get out small- to medium-sized dents out of your car. Just splash some hot water on both the plunger and the dent and start pushing and pulling until it pops out.

e34e36  
2017-03-31 09:49:48

LifeHacks - Using Boiling Water to Get Car Dents Out  |  More info

Heard about this tip and thought I'd give it a shot...it really works and with little effort..try it.

Recently featured on the Discovery Channel's Daily Planet episode that aired on 1/25/17. Came in at #2 in their Top 10 list.

Part 2:

New channel "Adam's Life Hacks". Subscribe below for more like content and feel free to leave any life hack video ideas you'd like to see in the comments section!

For any business inquiries, please contact adamslifehacks@gmail.com

e34e36  
2017-03-31 09:50:10

Paintless Dent Repair Using a Heat Gun and a Can of Compressed Gas Duster  |  More info

Can you repair dents in an automobile with a hair dryer and a can of compressed air? Yes and no. It depends upon the location and severity of the damage. But as I have demonstrated, with a heat gun, $9 worth of Endust Duster, and about 15 minutes, you can achieve some remarkable results.

Read more at...

Responses to the most common criticisms:

Q. Why didn't you just push the dent out from behind?

A. This is a hybrid vehicle and there is A/C equipment for battery cooling that is located between the sheet metal and the interior finish. The dent was simply not accessible from the inside.

Q. Why didn't you just use a toilet plunger and pull the dent out?

A. That may have worked on the larger of the two dents, but the surface area of the smaller dent would have made that impossible.

Q. This video and photos of the dents have been Photoshopped and faked!

A. Absolutely not. I will gladly attest that this video and the images of the dent, before and after, have not been retouched. I also have a witness who observed the process and would attest the same.

Q. "Tapping" the panel like you did in the video would have popped the dent out without the heating and cooling.

A. My attempts to pop the dent out with persuasive tapping by hand and a rubber mallet prior to the heating / cooling did not have any impact.

Q. This process didn't help, you can still see the dents!

A. Yes. if you look closely you can still see the smaller of the two dents. However, the larger of the two is not distinguishable to the casual observer. This process made a significant improvement to the appearance of both dents. It is not a factory perfect repair, but this is not a valuable vehicle either. I could not justify the expense of a professional body shop for a vehicle that is seven years old and +150,000 miles. This process provided a good alternative.


Reply